- Fits:
- HONDA CBR500R
- YAMAHA YZF1000 THUNDER ACE 96-00 R
- YAMAHA YZF600 THUNDER CAT 97-00 R
- YAMAHA ZEAL 91-94
- YAMAHA GRAND MAJESTY250 5VG [Where used] Right side
- ...and more.
2010년식 GSX-1250FA 순정 마스터 실린더 대용으로 설치하였습니다. 피팅은 완벽하게 잘맞고, 브레이크 조작감도 순정과 동일합니다.
다만, 브레이크액 리저브 탱크를 핸들에 고정시키는 볼트는 동봉되지 않아서 따로 구매해야 합니다. 나사산의 피치가 맞는 것을 찾는데 여러번의 시행착오를 겪었습니다. 제품은 매우 만족합니다.Read More - Fits:
- HONDA X4 TypeLD 97-01 (SC38)[Place of use]Front[Required quantity]2
- HONDA X4 TypeLD 97-01 (SC38)[Place of use]Rear[Required number]1
- HONDA XLR250R 91-94 (MD22)[Place of use]Rear[Required number]1
- HONDA CBR250R 88-89 (MC19)[Where used]Front[Required number]1
- HONDA VFR400R 87 (NC21)[Place of use]Front[Required number] 4
- ...and more.
A bit longer than intended for the front caliper. Maybe the pin I received is for the rear. But it fits properly on the front caliper anyway.Read More - Fits:
- HONDA CBR500R
- YAMAHA YZF1000 THUNDER ACE 96-00 R
- YAMAHA YZF600 THUNDER CAT 97-00 R
- YAMAHA ZEAL 91-94
- YAMAHA GRAND MAJESTY250 5VG [Where used] Right side
- ...and more.
I rebuild my bike up. There were a lot of Brake Master Cylinder on the market but I was hesitant because I was dubious from their manufacturer. I found this online for my Honda Bros NT400J 1988. I'm h...Read More - Fits:
- HONDA CBR400R 13-21
- HONDA CBR600F 95-98
- HONDA CBR400RR 88-99
- HONDA CBR400R 13-21
- HONDA CBR250RRR 17-21
- ...and more.
This is a replacement from the OEMDon't forget to check the part number and model number.There seem to be many types for CYGNUS, so it seems that we need to be careful not to buy the wrong one.I did t...Read More - Fits:
- HONDA X4 TypeLD 97-01 (SC38)[Place of use]Front[Required quantity]2
- HONDA X4 TypeLD 97-01 (SC38)[Place of use]Rear[Required number]1
- HONDA XLR250R 91-94 (MD22)[Place of use]Rear[Required number]1
- HONDA CBR250R 88-89 (MC19)[Where used]Front[Required number]1
- HONDA VFR400R 87 (NC21)[Place of use]Front[Required number] 4
- ...and more.
today i change the rear brake rotor and overhaul the caliper. the brake pin has seriously rusted and damaged so i cleaning all the surface of caliper and (not changed caliper piston...and Oring) and l...Read More - Fits:
- SUZUKI GSX400Type S 94-96 [Used point]Front double disk
- HONDA Silver wing400 02-08 [Used in]Rear
- YAMAHA MAJESTY125 01-03 [Used point]Front
- YAMAHA MAJESTYS 14-21 Installed at the same time as the stock shim [Location]Front
- HONDA Silver wing 01-08 ABS [part used]Rear
- ...and more.
I replaced OEMPad→Metallica→brembo in that order, and the controllability etc. is fine, but the Brake squeal just before stopping. (Noise Level) The "A" was so unusual that it could not be used for to...Read More - Fits:
- HONDA X4 TypeLD 97-01 (SC38)[Place of use]Front[Required quantity]2
- HONDA X4 TypeLD 97-01 (SC38)[Place of use]Rear[Required number]1
- HONDA XLR250R 91-94 (MD22)[Place of use]Rear[Required number]1
- HONDA CBR250R 88-89 (MC19)[Where used]Front[Required number]1
- HONDA VFR400R 87 (NC21)[Place of use]Front[Required number] 4
- ...and more.
First, let me say that this is a special case based on a combination of several conditions.After cleaning the Caliper, I put it back together, tightened the pad pin, and was finishing up by tightening...Read More - Fits:
- HONDA CBR400R 13-21
- HONDA CBR600F 95-98
- HONDA CBR400RR 88-99
- HONDA CBR400R 13-21
- HONDA CBR250RRR 17-21
- ...and more.
Neither good nor badBraking power was sufficient.Aggression to DISC does not seem to be that high.Read More - Fits:
- HONDA CBR400R 13-21
- HONDA CBR600F 95-98
- HONDA CBR400RR 88-99
- HONDA CBR400R 13-21
- HONDA CBR250RRR 17-21
- ...and more.
I think it works better than NORMAL.Red is now the Accent color and looks great.Read More - Fits:
- HONDA CBR400R 13-21
- HONDA CBR600F 95-98
- HONDA CBR400RR 88-99
- HONDA CBR400R 13-21
- HONDA CBR250RRR 17-21
- ...and more.
Used in CYGNUS.Personally, I prefer the way the braking force rises proportionally from the Brake lever input.It is recommended for those who make a kick rack to turn, enter a Corner while leaving a B...Read More - Fits:
- HONDA X4 TypeLD 97-01 (SC38)[Place of use]Front[Required quantity]2
- HONDA X4 TypeLD 97-01 (SC38)[Place of use]Rear[Required number]1
- HONDA XLR250R 91-94 (MD22)[Place of use]Rear[Required number]1
- HONDA CBR250R 88-89 (MC19)[Where used]Front[Required number]1
- HONDA VFR400R 87 (NC21)[Place of use]Front[Required number] 4
- ...and more.
For those who want to upgrade with OEM replacementIt's hard to lick, hard to decay, and also cool.Recommended for people who ride Honda motorcycles, but be careful with the length.Read More - Fits:
- KAWASAKI ZXR250R 90 [Frame No.]ZX250A-301501 or later
- KAWASAKI ZXR400 89 [ZX400] [Frame No.]ZX400H-000001 or later
- KAWASAKI ZXR250 95 [Frame No.]ZX250C
- KAWASAKI ZXR250 99 [Frame No.]ZX250C-020001 or later
- KAWASAKI ZXR250R 89 [Frame No.]ZX250A-300001 or later
- ...and more.
I've been sticking with the Tokico 6 pods. This time I adopted CaliperOverhaul and baked paint instead of OEM. I think it's a good corrosion protection. I've heard that some people use seal tape to pr...Read More - Fits:
- HONDA X4 TypeLD 97-01 (SC38)[Place of use]Front[Required quantity]2
- HONDA X4 TypeLD 97-01 (SC38)[Place of use]Rear[Required number]1
- HONDA XLR250R 91-94 (MD22)[Place of use]Rear[Required number]1
- HONDA CBR250R 88-89 (MC19)[Where used]Front[Required number]1
- HONDA VFR400R 87 (NC21)[Place of use]Front[Required number] 4
- ...and more.
Rust resistant Material:Stainless SteelPad pin。It is a little bit longer for one push for Caliper, but it can be used as it is with OEM and replacement.Features easy maintenance and performance retent...Read More - Fits:
- HONDA CBR400R 13-21
- HONDA CBR600F 95-98
- HONDA CBR400RR 88-99
- HONDA CBR400R 13-21
- HONDA CBR250RRR 17-21
- ...and more.
This is a replacement for the OEMPad and it works fine.Static power is also not a problem.Read More - Fits:
- KAWASAKI ZXR250R 90 [Frame No.]ZX250A-301501 or later
- KAWASAKI ZXR400 89 [ZX400] [Frame No.]ZX400H-000001 or later
- KAWASAKI ZXR250 95 [Frame No.]ZX250C
- KAWASAKI ZXR250 99 [Frame No.]ZX250C-020001 or later
- KAWASAKI ZXR250R 89 [Frame No.]ZX250A-300001 or later
- ...and more.
The OEM Bleeder Bolt is always going to Rust and Decay, so this Material:It is safer to replace it with Stainless Steel.Be sure to bleed the air and refill the fluid in the MASTER after replacement.Th...Read More - Fits:
- HONDA XL400VTRANSALP 92 ND06 [Frame No.]ND06-1000001 or later [Use part]Caliper side
- HONDA ST1100ST1100 PAN EUROPEAN 00 [part used] Caliper side
- HONDA X4 97-00 SC38 [part used]Caliper side
- HONDA X4 97 SC38 [Frame No.]SC38-1000001 or later [Use part]Caliper side
- HONDA XL400VTRANSALP 91 ND06 [Frame No.]ND06-1000001 or later [Use part]Caliper side
- ...and more.
ZrX1200 DAEG OEMHydraulic Clutch Bleeder Bolt This Material:I replaced it with a Stainless Steel one. The OEM Bleeder Bolt is made of steel and will always rust over time, so it's best to replace it. ...Read More - Fits:
- HONDA
- HONDA
- HONDA
- HONDA
- YAMAHA Majesty S 14-21
- ...and more.
I bought it because it is relatively Reasonable.I'm worried about being too cheap…Read More - Fits:
- HONDA CBR500R
- YAMAHA YZF1000 THUNDER ACE 96-00 R
- YAMAHA YZF600 THUNDER CAT 97-00 R
- YAMAHA ZEAL 91-94
- YAMAHA GRAND MAJESTY250 5VG [Where used] Right side
- ...and more.
In order to install the brembo 4Pot, the capacity of the OEMMASTER becomes insufficient and "Parenthesis is somehow good", so it was introduced. (Lol) wwwThere is no interference to Cowl because Separ...Read More - Fits:
- HONDA X4 TypeLD 97-01 (SC38)[Place of use]Front[Required quantity]2
- HONDA X4 TypeLD 97-01 (SC38)[Place of use]Rear[Required number]1
- HONDA XLR250R 91-94 (MD22)[Place of use]Rear[Required number]1
- HONDA CBR250R 88-89 (MC19)[Where used]Front[Required number]1
- HONDA VFR400R 87 (NC21)[Place of use]Front[Required number] 4
- ...and more.
Used for KLX125Compared to the OEM, the screw mountain part looked smaller, but I was able to install it without any problems.It's just the right length without the excess length that other people hav...Read More - Fits:
- HONDA
- HONDA
- HONDA
- HONDA
- YAMAHA Majesty S 14-21
- ...and more.
I'm happy with this Pad compared to the OEM!I am very satisfied with the price and availability of this product.Read More
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING