-08-8(Carburetor)*Drilling of switch hole is required|*You can use stock side cap. |*It is necessary to change the direction of the throttle cable, clutch cable and brake hose. |*It is necessary to change the direction of the brake banjo.
GRASS TRACKER Big Boy
09-12 (FI car)*You can use stock side caps.
GRASS TRACKER
-08 (Carburetor)*Drilling of switch holes is required. |*It is necessary to change the throttle cable, clutch cable and brake hose. |*It is necessary to change the direction of the brake banjo.
-04 *Processing to drill switch holes is required|* Required side cap (for 18mm I.D.)|*Not available for the models after 05 due to interference with the cowl.
ZRX400II
*Requires drilling of switch hole|*Applicable side cap (for 18mm dia.)|*Cannot be installed on models 05 and later due to interference with the cowl.
W400
*Required Switch Hole Drilled
ZEPHYRX
*Requires drilling of switch hole|* Requires side cap (for 18mm diameter)
Made in Japan.Prototype, installation confirmation and mass production are all under in-house management.These handlebars are made with a great deal of care and attention to detail, including careful selection of materials, several types of polishing, engraving of part numbers, high-precision bending and welding, and high-quality surface treatment, based on technology and know-how cultivated over many years in Osaka in Japan.STKM13A steel material with excellent tensile strength is used.Cleared by JMCA safety standard value.Triple nickel and chrome plating (3 layers of nickel and chrome) finish with thick film and excellent durability and corrosion resistance.
Points of Attention
* If there may be an instruction manual included, it will be written in Japanese.
Fits: KAWASAKI W400 *Required Switch Hole Drilled, KAWASAKI ZRX400 -04 *Processing to drill switch holes is required|* Required side cap (for 18mm I.D.)|*Not available for the models after 05 due to interference with the cowl., HONDA MONKEY 84-07 (1600008-/AB27-1000001-1899999)* Requires Top Bridge H30 Holder or MONKEY Handle Holder, HONDA HORNET250 *Need to drill switch hole, HONDA MONKEY 09-12 (AB27)(1900001-)(FI Vehicle)*Requires top bridge with H30 holder or MONKEY handle holder|*Requires switch hole drilling
เป็นแฮนด์ที่หามานานในเมืองไทย แต่ไม่มีเลย มีโอกาสได้มาเจอในเวปนี้ สวยงามมากสำหรับแฮนด์รุ่นนี้ สั่งมาใส่แล้วจะกลับมารายงานอีกรอบครับThis is a long hand in Thailand, but no chance to meet in this web. Very beautiful for this model. I will post back to report it offline.(translated by Google Translator)View Detail
Fits: KAWASAKI W400 *Required Switch Hole Drilled, KAWASAKI ZRX400 -04 *Processing to drill switch holes is required|* Required side cap (for 18mm I.D.)|*Not available for the models after 05 due to interference with the cowl., HONDA MONKEY 84-07 (1600008-/AB27-1000001-1899999)* Requires Top Bridge H30 Holder or MONKEY Handle Holder, HONDA HORNET250 *Need to drill switch hole, HONDA MONKEY 09-12 (AB27)(1900001-)(FI Vehicle)*Requires top bridge with H30 holder or MONKEY handle holder|*Requires switch hole drilling
I was on the w650 OEMUp Handlebar, but the posture became upright, all the input from the road surface became Damage to the spine. After making this Handlebar, the wind on the highway no longer cared about, and the pass also became easier to run. Cable thrusts between Handlebar and Tank, Clutch Wire threaded to the other side of Handlebar, Brake hose slacked out fixed parts and this Handlebar does not go through a car inspection, so return to OEMUp Handle every two years. It is not said.View Detail
Fits: KAWASAKI W400 *Required Switch Hole Drilled, KAWASAKI ZRX400 -04 *Processing to drill switch holes is required|* Required side cap (for 18mm I.D.)|*Not available for the models after 05 due to interference with the cowl., HONDA MONKEY 84-07 (1600008-/AB27-1000001-1899999)* Requires Top Bridge H30 Holder or MONKEY Handle Holder, HONDA HORNET250 *Need to drill switch hole, HONDA MONKEY 09-12 (AB27)(1900001-)(FI Vehicle)*Requires top bridge with H30 holder or MONKEY handle holder|*Requires switch hole drilling
It stopped hesitatingly whether making it a separate handle, and although he thought that he would make it a swallow, it was cheap here and it made it this. It attached and surprise, a silhouette and atmosphere, and the riding taste were ideal. Although it will not go out if it is a separate handle since the tank of a hornet is large, this goes out just before. Since the silhouette became a racy atmosphere although anteversion was not so tight as it considered, either, it is large satisfaction. Since the becoming [ a more sharp impression ] kana ? was thought when it was a swallow, they are four stars. I would like to raise five individually.View Detail
Fits: KAWASAKI ZRX400II *Requires drilling of switch hole|*Applicable side cap (for 18mm dia.)|*Cannot be installed on models 05 and later due to interference with the cowl., KAWASAKI W400 *Required Switch Hole Drilled, KAWASAKI ZRX400 -04 *Processing to drill switch holes is required|* Required side cap (for 18mm I.D.)|*Not available for the models after 05 due to interference with the cowl., HONDA MONKEY 84-07 (Z50J-1600008-|AB27-1000001-1899999)*With Top Bridge H30 Holder or MONKEY Handle Holder required, HONDA HORNET250 *Need to drill switch hole
I reverse engineered it on my XJR1300. I was not satisfied with the position and appearance of the Tommaselli separate handlebar I had previously installed, so I changed to a Pipe Handlebar. This was the best Pipe Handlebar to shift the position forward. I also shifted the position of the Handlebar Post to get a good position.
I agree with the Position and the look.View Detail
Fits: KAWASAKI ZRX400II *Requires drilling of switch hole|*Applicable side cap (for 18mm dia.)|*Cannot be installed on models 05 and later due to interference with the cowl., KAWASAKI W400 *Required Switch Hole Drilled, KAWASAKI ZRX400 -04 *Processing to drill switch holes is required|* Required side cap (for 18mm I.D.)|*Not available for the models after 05 due to interference with the cowl., HONDA MONKEY 84-07 (Z50J-1600008-|AB27-1000001-1899999)*With Top Bridge H30 Holder or MONKEY Handle Holder required, HONDA HORNET250 *Need to drill switch hole
Initially I put in Spacer, because Seat is common with NINJA, because I can not deal with Riding with the z250 knee stretched, so the thing like a forward tilting Separate handle is still better. I also thought of Condor, but as for COSPA and former SR riding, HURRICANE 's Conti is preferred, so I wonder if it fits Fire? I thought, but I am satisfied with Large on my own terms. The body pain due to Position almost disappeared. Since it was not a conforming model, it is necessary to change the handling of Clutch Wire and change the angle of Brake hose, but it is somehow NORMAL and Large is durable. Switch was perfect if hole was open. Although it was a good translation from the beginning, it was a good translation, but with Z's Styling Position of NINJA, I am satisfied with Large now. I hope you find it useful.View Detail
* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
Get on your grid by register your motorcycle! About our "Mybike" service
"Easier to Search Items" It helps you to search items to fit for your motorcycle!
"Get Much Valuable Information" It helps you to get special deals, newly listed items and closeouts about your motorcycle!
"Easy to Register" It requires only your motorcycle manufacturer, model name and model year!