Once you select the option, estimate delivery time will be displayed.
*Shipping date and Estimate time of arrival are not guarantee.
Once your orders are placed, we will check the stock of manufacturer and send you the confirmed Shipping time via e-mail.
[Swingarm Pipe Shape] Triple Square [Material] Aluminum 7N01, A5083 material used [Model] GROM (For early and late models)
[Recommended number of chain links] +0cm:No change +6cm:120 +10cm:130 *It depends on the number of sprockets you are using.Adjust with a chain cutter or similar tool.
[Components] 1) Chain adjuster - 1 set (for each pipe shape) 2) Shock mounting bolt set Bolt - 1 (Repair part number 691765) Nut - 1 (Repair part number 65229) Washers - 2 (Repair Part No. 65090/1pc.) 3) Axle shaft 275mm - 1 (Repair part number 38066) 4) Axle nut M12 - 1 (Repair part number 38001)
*The 10cm long side stand is not long enough, please use the Aluminum Adjustable Stand (32037).After replacing the stand, the side stand switch cannot be used, so the sensor switch must be connected directly.Also, since there is a possibility of interference between the rear fender and the tire, please use a fender eliminator kit (recommended by Kitaco). *The image contains an image for each option. *2016 models with stock exhaust cannot be installed only with stabilizer (stabilizer interferes with exhaust catalyzer). *There may be changes in product specifications due to the manufacturer's reasons.
Aluminum swingarm for GROM / MSX125. 7N01 material used Swingarm Weight: Stock 3.5kg→1.8kg (Triple Square, No Stabilizer, +0cm) The swingarm is made of aluminum 7N01 material, which is 1.8kg lighter and more rigid than the stock swingarm weighing 3.5kg, and improves the operability of the motorcycle by reducing the unsprung weight.
■Option Description ・Additional fender brackets Add a bracket so that the stock rear fender can be installed.Since the bracket is bolted, it is possible to remove it. ・Chain slider specification Chain slider bolted specification Change the chain slider from riveted to bolted.Easy to replace when worn out. ・Option: Pivot section structure Pivot section ball bearing change The pivot part that normally uses bushings is converted to ball bearings. ・Additional processing of stand hook base Additional processing of stand hook base (M6) G-Craft stand hook or aftermarket stand hook (M6) can be attached. ・Chain pull specification Racing stand hook specification OW type chain adjuster processing The chain puller is tapered to eliminate vertical misalignment of the axle shaft. The tapered frame moves so there is no vertical misalignment.This mechanism is also used for swingarms of big bikes. G-Craft Part Number: The 32071, 32072 and 32073 racing stand hooks can be installed. *G Craft Part Number: 33170AP Lockheed caliper support cannot be installed (will interfere)
Points of Attention
* If there may be an instruction manual included, it will be written in Japanese.
In addition to the appearance, the Merit is that the suspension movement is less likely to be disturbed due to its high precision, the chain alignment is less likely to go out of alignment, the weight is reduced, the rigidity is increased due to the structure, and the comfort and stability of the ride is improved by extending the swing arm. The two options on the market that can be clearly Upgrading from OEMSwing Arm are G'craft or OVER. The two are full of Merit in terms of both dress-up and practical use, except for the price.View Detail
First of all, 6 cm Long needs Chain's Length change Death! 115~117LINKDeath! If you measure Brake hose you can even NORMAL Death! But since it takes impossible to change it is better to change DEATH !!!!!! Light weight and weight is obviously different from OEM! It's not only weight The rotation of the Tire is somewhat light The movement of RShock is also light (With Bearing) Afterwards satisfaction is Zuzzuzuuuuuuuun
And finally, OEMRear, Axle Shaft was demon Rust Probably inside of Wheel would be Rust's nest Is not it cracked in a little more? Rust was Southeast ASIA Quality It took me a lot of hard time getting metaxso while pulling it out I already took Hammer in a crushing thunderView Detail
* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
Get on your grid by register your motorcycle! About our "Mybike" service
"Easier to Search Items" It helps you to search items to fit for your motorcycle!
"Get Much Valuable Information" It helps you to get special deals, newly listed items and closeouts about your motorcycle!
"Easy to Register" It requires only your motorcycle manufacturer, model name and model year!