Speed Wide Tuning Run Plate
Product # RP-YS01
39,943.81 MMK (2,875 JPY)
List price: 39,943.81 MMK Save 0%
+29 Webike point (402.91 MMK)
This item is discontinued. |
Fitment
- Cygnus X Model 5 (SED8J)
- Cygnus XVehicles using genuine pulleys
Product # RP-YS01
39,943.81 MMK (2,875 JPY)
List price: 39,943.81 MMK Save 0%
+29 Webike point (402.91 MMK)
This item is discontinued. |
Fitment
Model Page Links
Fits: YAMAHA , YAMAHA Cygnus X Vehicles using genuine pulleys
I installed it on 1YP2, and replaced it based on the Review. Before the replacement, it was maintained at 7-8,000 RPM.
After the replacement, the gearshift is shifted at 6,000 to 8,000 rpm, depending on the Axel opening, to prevent excessive rpm. Fuel consumption has also improved.
I don't know about the maximum speed, but I thought it would be impossible to achieve balance in the practical range. Durability etc. is unknown.
I did not give it the highest rating, but it was the best Matching for the current Spec.View Detail
Fits: YAMAHA , YAMAHA Cygnus X Vehicles using genuine pulleys
I put it on a Type 1 SE12J 125cc.
First of all, installation was not possible. because the processing of Spline was bad and did not go in, it was possible to cut with File. I did.
When I installed it, the paint on the surface of the WR's hit surface came off immediately after just a test run.
I put it on my High Speed Pulley and the shifting is fast. It's similar to a lighter WR.View Detail
Fits: YAMAHA , YAMAHA Cygnus X Vehicles using genuine pulleys
As a result of various exchanges, speed of 40 km / h / The condition of h or better improved, but 40 km / Acceleration of less than h was getting worse. I was cheating with Drive face and Shim washer, but it was another one.
As a result of exchanging with this Ramp Plate, it was possible to increase the amount of Shim washer, it became possible to raise the engine speed at low speed, and the acceleration became better.
I am concerned that the grooves where Pulley's Weight roller moves and the contact surface of Weight Roller of this Ramp Plate are out of alignment. Even if you compare it with Pulley of NORMAL, it is misplaced.
I think that it is easier to adjust if the shift width is slightly smaller.View Detail
Fits: YAMAHA , YAMAHA Cygnus X Vehicles using genuine pulleys
I did not put in Shim washer that I dislike that the high speed will not grow until now. This time I attached this Ramp Plate and it became possible to change the speed on the high speed side so Shim washer added 1 mm stuff adds and the speed and speed have improved better than before.
However Engine Displacement Volume 125 cc remains, but we do not know if it will be helpful as we are raising the Engine Power.View Detail
To continue viewing this product on Japan domestic webike (in Japanese), press "Go to Japan Domestic".
Notification
Please select option before add to your cart.
Customer Service
INFORMATION
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING
* The BEST and MUST store to find Japanese parts.
* Register now for amazing deals and other special offers!
* Over 800,000 listed items. It's hard NOT to find your parts.
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.