■Exclusive products for racing [Material] FRP [Surface finish] White gel coat finish
*The white gel coat of this product is a thin coat. *The white gelcoat may have bubble-like indentations on the surface. *We do not accept returns or exchanges due to bubble-like indentations on the white gelcoat surface. *White gelcoat finish is a base material for painting that is intended to be painted.Therefore, please paint it before use.
*The installation of models is not checked other than those listed in the compatibility check list.If your vehicle is not listed, it cannot be installed or has not been tested. *The installation of the product to the models that are not listed in the compatibility check list is not guaranteed. *The color of the product may vary depending on the shooting conditions, monitor, product lot, and left and right of the set product. *Images may contain other products. *There may be changes in product specifications due to the manufacturer's reasons.
The size of the numbered part is designed to accept oil in accordance with the HRC GROM CUP regulations. All necessary brackets for installation are included.
Points of Attention
* If there may be an instruction manual included, it will be written in Japanese.
Molding quality and texture is fairly good its to be expected from fiberglass resin made. I like the fact it comes with all the mounting hardware which makes installation easy. The blue markings i made on the product are areas i need to grind or cut off due to my exhaust set up which i am very aware of before purchasing it, i knew i would be modifying it to make it fit. Product was well packaged and protected. I would advice anyone who purchase this cowl to be aware of what type of exhaust set up you have and be prepared for minor modification but if your a Do It Yourself like myself, it shouldn't be difficult to work around modifying it. On a side note you will need to paint it with the color of your choice as well.View Detail
Satisfied with Total first. I am satisfied with the Refreshing look of the lower part of the Engine. I think it can be installed in NORMAL condition. Brake pedal may interfere a little. (I think it depends on the individual) Installation was rather easy with Bracket. Next is the Cowl Mounting Bolt. In my case, I was concerned about the directness of the bolt, so I purchased KITACO's Nylon washer separately and tightened it. However, over, GP-PERFORMANCE Full Titaniumium Full Exhaust Muffler interferes with it, so a small modification is required. (This shape same type may interfere) Also, GCraft's "Chikki-kun" (a small, sturdy, and strong machine) also needs to be processed. I have attached a photo for your reference. I processed it myself with BabyGrinder, so it doesn't look great! (TT) If you have a regulation such as Race, you may need to be careful because the Exhaust System part has been cut off. I was shaving it off for the purpose of dress-up. I had expected that. The painting was done with Holtz's Luster Erase Black and Luster Erase Clear, but it was my first attempt at painting and I hid the failed areas with Sticker. (Chuckles) I noticed some spots on the bottom coat of Black, but it was too late, so I continued on with it, but we'll see what happens. If it comes off, I will have to reapply. I'm sure you all do a good job of prepping your work, but since it was a gel coat, you shouldn't cut corners just because you think it's good. The Spray I bought this time is used up, so I'll see how it goes and if it doesn't work, I'll probably repaint it. The value is also there, so I would like to request that the mussels be kept after the Gel coat is painted, even if only temporarily. I'm looking at this from a beginner's perspective, so some mistakes may be unavoidable. I also think Large sturdy because you all don't cut corners. After a short run at the end, the lower part of the Under Cowl was warm and the heat from the exhaust pipe was transmitted. There was a gap of more than half a finger and less than one finger, which is a little worrisome. It depends on the future.View Detail
[How is it used? It's nice to cut the wind. Was the one you received as per Image? Street Image Was the installation difficult? There was no Instruction Manual, so I was a little worried. How was your experience with it? Custom look [Included Parts:were they on? It comes with Bolt and Bracket [Was there anything that disappointed you? I want the Instruction Manual to come with it, just a sheet of paper. Other items that would be helpful No Instruction Manual/Request Instruction Manual is attached.View Detail
* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
Get on your grid by register your motorcycle! About our "Mybike" service
"Easier to Search Items" It helps you to search items to fit for your motorcycle!
"Get Much Valuable Information" It helps you to get special deals, newly listed items and closeouts about your motorcycle!
"Easy to Register" It requires only your motorcycle manufacturer, model name and model year!