Pulley kit released by M-FACTORY's original brand MFR. Comes with body, lamp plate, boss and weight roller. Compatible with TODAY, NEW TODAY, 4-stroke Dio, Dio Chester (4-stroke carburetor), etc.! *Currently, we are confirming the applicable models *Because of individual differences in the vehicles, the performance may not always be equivalent to the power curve.Depending on the vehicle, you may need to fine-tune the weight rollers. *Installation instructions are not included.We will not exchange, return, or refund any items that are defective due to mishandling. *Some products require special tools, special work, or a mechanic's license for installation and maintenance.Even if technical problems arise with the installation, we will not be able to respond to any inquiries regarding installation or handling. *We do not accept returns or exchanges at the customer's convenience.
It compensates for the weak points of 4-stroke 50cc scooters, namely acceleration and maximum speed, and achieves even better output characteristics.
Points of Attention
* If there may be an instruction manual included, it will be written in Japanese.
One season of operation showed that the variator is not being finalized. or rather, the belt does not go out to the full radius. The rollers have wear on one side.View Detail
2011 year model JBH-AF68 DIO 50cc mileage is about 9200 Km Clutch, Belt is a thing of OEM that I use without replacing from new car purchase Weight Roller is the cheapest way of DAYTONA 5. It is 33 g of 5 g × 6 Weight is 68 kg Gram
Approximately 73 km in flat without angle / h Approximately 77 km when going down / H seems to have been out The climb is about 40 km / About the same as h (If you want to keep climb speed above 50 kg, OEM Pulley and Pulley boss 5. We recommend using 5 g × 6 Weight Roller)
Acceleration in the flat is the same as NORMAL etc. However, since it becomes considerably blunt at the ascent slope, we recommend that you use it for the car that was Bore up
Because it was Pulley who seemed to be good to buy, the evaluation is high but since we can not evaluate it because we are not using the attached Weight Roller, 4. I made it to 8 View Detail
Initial Model TODAY received from a friend (carburetor) is. NORMAL soon took refuge and it took a Rev limiter and was scared of on the main road. Belt and Clutch were intact, exchanged only for Pulley Department, but it is drastic change. Without increasing the number of revolutions, I feel that shifting at Torque's delicious places is going on, the Engine sound also gets quiet and it is getting excited, although the acceleration is getting better, the speed range also improves, and quiet. Image remodeling was bad and smoked, but this is also good making, reputation reason. It was good that Mr. Kami was pleased with anything else.View Detail
Therefore, since it becomes an impression when using with SPACY 100, I think that it is different from when used for Today.
Mounting accuracy There is no problem, I attached SPACY with non-processed ponto. Both Roller's rolling surface and Sieve surface are beautiful.
Quality, texture The appearance is beautiful. However, since damage report of attached Slider was seen with Net, I made it to OEM Parts Number from the time of installation just in case.
Performance Both start acceleration and intermediate acceleration are satisfied. As for the Top, since Pulley outer diameter is Small, it may be a matter of seriously setting out Engine or other settings, but in NORMAL vehicles, I did not understand the difference.
durability When we opened it after hundreds of kilometers of traveling, weight roller was out of three of six and slightly worn out. However, because similar symptoms appeared also in the thing of CHAMELEON FACTORY used before, although it can not be said that this Pulley is bad ...
Cost performance I think that it is cheap and good item.
Also, regarding the Weight roller, it was too light for the accessories, so separately 9. Changed to 5 × 6.View Detail
M-Factory TODAY/NEW TODAY MFR Hyper PulleyEasy five minute job to install on standard 50cc honda today.gave me 10 kph increase from 55 to 65.with more power it would go faster because it was on the 8000rpm ignition governor before at 55kph.very happy result for the money.and very fast delivery to Australia.so 5 stars from me.View Detail
* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
Get on your grid by register your motorcycle! About our "Mybike" service
"Easier to Search Items" It helps you to search items to fit for your motorcycle!
"Get Much Valuable Information" It helps you to get special deals, newly listed items and closeouts about your motorcycle!
"Easy to Register" It requires only your motorcycle manufacturer, model name and model year!