Exhaust Gasket

Fits:YAMAHA BirdCity 125 18 BU54 SEC1J, YAMAHA BirdCity 125 14-16 2CM9/2CMN SE82J, YAMAHA CYGNUS Gryphus 22-24 BKG1/2/3/4/5 SEJ4J, YAMAHA XSR125 24 BVF1 RE46J, YAMAHA MT-125 23 BVE1 RE45J

MoneyPig

Excellent

Jan 7, 2023

高性价比配件

我的摩托车是YAMAHA NMAX155，按照摩托车保养说明书每次拆卸排气都需要更换消音器垫片，消声器垫片是保养和维修的必备品。它是不能重复使用的易损件。反复使用可能会造成排气泄漏，使系统无法发挥其预期功能。KITACO垫片价格比原厂垫片价格便宜，性能完全一致。

Helpful?

Fits:YAMAHA BirdCity 125 18 BU54 SEC1J, YAMAHA BirdCity 125 14-16 2CM9/2CMN SE82J, YAMAHA CYGNUS Gryphus 22-24 BKG1/2/3/4/5 SEJ4J, YAMAHA XSR125 24 BVF1 RE46J, YAMAHA MT-125 23 BVE1 RE45J

Japanese Webike user

Excellent

Sep 22, 2020

As an alternative.

Since the OEM Exhaust Gasket for parallel import cars is imported with the Exhaust System replacement, I used this product with the same part number as the replacement. No problem.

Helpful?

Fits:YAMAHA BirdCity 125 18 BU54 SEC1J, YAMAHA BirdCity 125 14-16 2CM9/2CMN SE82J, YAMAHA CYGNUS Gryphus 22-24 BKG1/2/3/4/5 SEJ4J, YAMAHA XSR125 24 BVF1 RE46J, YAMAHA MT-125 23 BVE1 RE45J

Japanese Webike user

Excellent

Jul 19, 2020

It's pretty thick.

I bought it when I was replacing the exhaust system on my Aerox.
Since it has the same engine as N-MAX, we chose this product to fit the N-MAX vehicle.

I don't know about the quality or continuity of the product, but I did notice that it was quite thick.
The thickness itself is correct (the effect is achieved by crushing the Gasket), but I felt it was much thicker than the KSR-50.

I thought at the time of the KSR-50, but it is a single cylinder but the Gasket is Quantity:2pc. It's a bit strange that it's sold as a set. Normally, 1pc. would be fine.

By the way, the Engine side of the Aerox 155 was just size with the holes on the Engine side.
The groove to attach the gasket to the exhaust system you purchased? I probably shouldn't have put it on for safety reasons, since there was no...

Helpful?

KITACO Exhaust System Gasket yamaha nmax

Fits:YAMAHA BirdCity 125 18 BU54 SEC1J, YAMAHA BirdCity 125 14-16 2CM9/2CMN SE82J, YAMAHA CYGNUS Gryphus 22-24 BKG1/2/3/4/5 SEJ4J, YAMAHA XSR125 24 BVF1 RE46J, YAMAHA MT-125 23 BVE1 RE45J

Fauzi M

Very Good

Feb 12, 2019

my 2nd review, still haven't installed the kitaco gasket in my nmax 155 yet (standard head)... however i managed to draft a chart of certain gaskets i have used in my yamaha nmax 155 standard block and head... maybe it could be useful for the users and also the manufacturer to check back the configuration...for the gaskets i have bought i guessed i could use them in my another nmax (yes, i have 2) which is a full racing specs with a 23/22 18/19 superhead. i hope this might help others in choosing the right gasket for their bikes especially the yamaha nmax 155cc.

Helpful?

kitaco exhaust gasket for yamaha nmax

Fits:YAMAHA BirdCity 125 18 BU54 SEC1J, YAMAHA BirdCity 125 14-16 2CM9/2CMN SE82J, YAMAHA CYGNUS Gryphus 22-24 BKG1/2/3/4/5 SEJ4J, YAMAHA XSR125 24 BVF1 RE46J, YAMAHA MT-125 23 BVE1 RE45J

Fauzi M

Average

Feb 11, 2019

i haven't tried this kitaco gasket for my yamaha nmax 155cc yet but I'm quite worried as from my measurement this kitaco gasket diameter (37.2mm) and thickness (5mm) are different from my previous measured gasket which is 35mm of its diameter and of 3.5mm thickness. as i can remember the 35mm diameter gasket fitted in just perfectly as the cylinder head exhaust port's size. and as it is a crushed gasket I'm more worried that after crushing the gasket in then the hole from the exhaust port and the exhaust header would be affected, if so then performance might be compromised. however after i dismantle the exhaust header then I'll be sure about everything. i just hope that i can use the kitaco gasket for my nmax as 'plug and play' type.